Running 10-20 lines with FreePBX on LTE/4G/3G Wireless Data Plan
@abefroman wrote: Does anyone have experience running a phone server over a wireless data network? How would this work for 10-20 lines going at once on 3G (connected to a single router which accesses...
View ArticleConfiguring a Grandstream HT503 Device to act as an FXO Gateway
@GeekBoy wrote: So I got me one of those HT503s. Now I am going on this article as listed in the title of this topic. Configuring a Grandstream HT503 Device to act as an FXO Gateway (and the whys...
View ArticleUnable to register Cisco 7965 - REGISTER transaction (key exists)
@rsarceno wrote: Asterisk 13.9.1 Freepbx 13.0.190.7Chan_SIP ext 5001, I can register using Cisco 7960 but when I tried the same extension using Cisco 7965, I'm getting a warning message [2016-12-28...
View ArticleSangoma S500 VPN enabled not working when site to site VPN exists
@gwntc wrote: I have a few S500 phones. When I configure the users phone to use the VPN profile it works fine when they are connected from a location that isn't also configured with a site to site VPN...
View ArticlePCI card for GSM?
@bgroper wrote: I'd like to add a single GSM connection to a small FreePBX server.Will be used for both inbound and outbound routes.Any suggestions for suitable low-cost hardwares ? Entry-level PCI...
View ArticleHow to install apt-get
@MathiasJ wrote: Hi! I want to install additional Software at my machine.But This Linux doesn't Support apt-get.So I like to ask how to install it.I was already at some Forums but the link to install...
View ArticleClik here to view.
Upgrading from Free PBX 12 to 13
@Thepublican2 wrote: Hello, I am at a loss as to the correct way to upgrade. I understand there is a built in module available entitled "PBX Upgrader" but when I ran this, the version number was out...
View ArticleClik here to view.
No audio on extensions with voxbeam trunk
@mauritz wrote: We have a freepbx13 / centos 7 installation - The installation currently is working perfectly with our main DID (incoming and outgoing calls). We want to test voxbeam services and have...
View ArticleRepo for commercial modules not available
@paradonym wrote: We set up an CentOS 7 server to use FreePBX with commercial modules, after initial setup and testing also with purchased modules. The dependencies can't be compiled for Debian Linux,...
View ArticleChanspy listen acts like barge (both sides can hear me)
@ghurty wrote: I am trying to get whisper to work, but instead of whisper both sides can hear me. Chanspy listen does work.This is what I have for listen (which does work)exten =>...
View ArticleExtension blocking
@loic wrote: Hello!I need help.I have freepbx(~1500 extensions, calls simultaneously is less than 50).Telephones connect to VoIP gateways.Inbound calls realise:Inbound...
View ArticleCall recording with custom dialplan
@arainero wrote: Hello everyone, I have created a custom pre-dialout trunk dialplan that will use a different area code depending on what area code is dialed. It looks like this:...
View ArticleIssues with Queues and transferred calls?
@rymes wrote: We are having an issue with agents not receiving calls until they log in and then back out. It seems to be the same issue reported here:...
View ArticleTftboot Firmware Question
@Cothirteen wrote: I tried to find info that I could on this and maybe it's one of those where I am just not sure how to word it. My basic question is do I only need the firmware for the model phones...
View ArticleSip Timer T1 and B?
@rymes wrote: So, I was searching for something else today and stumbled across this link, suggesting that admins of busy Asterisk systems consider tuning these two settings...
View ArticleChannel.c:6009 ast_request: No channel type registered for ” - Ast 11 -...
@FreeSWServers wrote: I am getting "All Circuits are Busy" on outbound calls, on a system that used to work. Its CentOS 7 w/ Asterisk 11 and FreePBX 12. Here are the errors from the debug: [2017-01-03...
View ArticlePhone call pausing help
@pixa241 wrote: I am on the latest FreePBX and the issue we are running into is randomly while on a call the voice will pause for about 2 seconds, so I can not hear anything or vice versa then it...
View ArticleHow to restore a dead machine?
@digiteltlc wrote: Possible scenario:I have a full backup. My pbx HDD is gone .Replace HDD, fresh install of latest FreePbx distro , restore backup. Is this enough ?? I mean, backup can come from an...
View ArticleCIsco SPA509g fails to provision after edditing Expansion Module BLFs
@directcurrent13 wrote: After editing Expansion Module BLFs in the end point manager, all the phones in the system including those without expansion modules fail to provision after a endpoint reset....
View ArticlePlaying (unsuccessfully) with a Panasonic IP camera
@digiteltlc wrote: just received a new Panasonic KX-NTV150 communication cameraIt includes a SIP client to be registered to a (Panasonic) PBXSIP configuration has the usual parameters, user, pass,...
View Article