Web Console Authentications "Invalid username or password" (after login)
@twinman wrote: Was running 10.13.66-12. No issues until yesterday morning. Although no patches were applied, we could not login to any web interface (admin console) without receiving a message,...
View ArticleSetting TX gain and RX gain not working in dahdi config > global settings
@tom_88 wrote: I'm having trouble increasing the transmits and receive gain for my Sangoma A200 FXO card. The card is already setup and running the way I want for the most part, however the phone...
View ArticleNo swap message in gui
@alexcal wrote: Hi,I'm getting this message in notification area, it does not give any instructions but says: Your system has no swap space. This should be fixed as soon as possible. Once fixed issue...
View ArticleProblems to make calls after hanging
@dirweb wrote: Hellolately I'm detecting problems when trying to make a phone call immediately after i hangup another call.Basically if I try to callnot hear anything but the other side respondAt that...
View ArticleProblem with Polycom IP5000
@richgoldmd wrote: Hi, I recently acquired 3 polycom IP5000 phones, and I am trying to get them set up with my server. These are POE phones, and I have a 3COM 4500 PWR router, basic setup, POE...
View ArticleClik here to view.
Solved** Problem Upgrading from 12 to 13
@garias wrote: hello guys im getting this error Pasted image1920x1080 231 KB doing this: fwconsole ma upgradeall Pasted image1920x1080 12.7 KB any help on that issue ? Posts: 3 Participants: 2 Read...
View ArticleFreepbx Video (Help................)
@russr wrote: Hi, Can somebody please help...I'm stuck and can't seem to get it workingI am trying to get video calls working in freepbx but can't seem to do that.I am using x-lite as a softphone on a...
View ArticlecelSQL Exception after converting to remote CDR DB
@adamskalicky wrote: Hi All, I recently converted my CDR to use a remote DB and also migrated CEL over with it. All is good, I can hit my CDR reports and they load properly, I can see both CDR and CEL...
View ArticleOutbaound Caller-ID for SIP trunks
@psdk wrote: May I did wrong but in my cases, when I configure SIP trunks between FreePBX servers or Elastix or others, Caller id of calls is equal with 'fromuser' or 'dialed number' (rpid), and...
View ArticleOutbound call via E1 PRI card fails with error code DIALSTATUS = CONGESTION...
@piyushaghera wrote: Hello,Below is my environment:FreePBX: 13.0.98Asterisk: 13.7.2Ubuntu: 14.4E1 PRI card: Allo 3rd Gen 2 port PRI card I had installed above card and connected ISDN PRI line to...
View ArticleDisable follow me by feature code
@stegfeld wrote: hi, I want to disable follow me for my own extension on my telephone by feature code. this should be possible described in free pbx wiki...
View ArticleSolved** Plaint Text Extensions File
@garias wrote: hello i wanted to know where i can find the file that freepbx saves extensions information. i need to edit manually an extension to add sip uri dial. Posts: 3 Participants: 2 Read full...
View ArticleCannot place call on hold
@SilkBC wrote: Hello, I have an odd issue that makes zero sense to me. I am not sure of it is problem with asterisk/FreePBX or the phone sets themselves. I have a new install: Asterisk 13 PBX...
View Article[SOLVED] Activate mailbox without calling it
@zirophyz wrote: Hi, Is there a way to activate a voicemail mailbox without dialling into it via 98/97? (Working on a remote system that I can't register to, they've sent me greetings but as the...
View ArticleCall Drops When Answered in Ring Group
@bgrubbs wrote: I have a ring group setup to ring 3 extensions simultaneously (ringall) when a call comes in from outside. Whenever one of the extensions answers, the call immediately terminates. I’d...
View ArticleParked Calls Dropping
@Novais wrote: Have a strange situation where a call comes in and is answered no problem. Call is then Blind Transferred to parking lot 70 (default) and the call appears to be successfully parked, the...
View ArticleHow can I, either using the DAHDI freepbx module or editing a conf file set...
@ghurty wrote: How can I, either using the DAHDI freepbx module or editing a conf file set which T1 one card/span comes first? I have three T1 cards, two of them are four ports and one is a single...
View ArticleClik here to view.
Randomly error
@garias wrote: hello i am gettign this error trying to apply setting, or when hit submit button Pasted image1920x1080 173 KB any help on what causing this ?? Posts: 1 Participants: 1 Read full topic
View ArticleLimit outbound routes for certain extensions
@mitch2k wrote: Hi, I use freepbx for a multibrand company. I have created 3 outbound routes:If you dial 1* you use the CID of brand AIf you dial 2* you use the CID of brand BIf you dial 3* you use...
View ArticleNo incoming calls "number out of service" help needed
@Eres wrote: Hi, Im having some real issues with receiving a call (no outbound problems). When i call the number i get "The number you have dailed is not in service". I did a lot of resreach on the...
View Article