FreePBX & Cisco SPA phones getting random 486 busy signals?
@richtj99 wrote: Hi, I am having an issue with a Freepbx installation. The initial install was in 5/2015 & has about 20 Cisco SPA504G phones. My problem is that I am getting a 'random' 486 busy...
View ArticlePresence stops triggering follow me
@wolfer201 wrote: Presence normally works fine, however occasionally (at least once every other week), changing presence stops triggering follow me. Reboot the server and everything works fine again....
View ArticleUser Manager AD Auth Cannot Sign In
@tekz08 wrote: I've got two separate FreePBX installations that I've switched over to AD authentication for our User Manager accounts. Details on servers... Server 1:FreePBX 13.0.187Asterisk version...
View ArticleModify T38FaxMaxDatagram value
@haximo wrote: I'm trying to modify the T38FaxMaxDatagram value in order to resolve the following error when trying to send faxes: UDPTL asked to send 146 bytes of IFP when far end only prepared to...
View ArticleAnnounce Name Before Greeting on extension Voicemail
@gmeyer30 wrote: Is it possible to force the recorded name to be played before the greeting when reaching an extensions voicemail? Posts: 3 Participants: 2 Read full topic
View ArticleClik here to view.
Incoming calls randomly answered by playback message - Help_Thanks
@imcontreras wrote: Some incoming calls go straight to playback message: "The number you dialed is not in service please check your number and dial again" Inbound route Set Destination: ring group PBX...
View ArticleSending Blacklist calls to a custom destination in version 12
@bcunningham wrote: We are still on version 12 of FreePBX, and since we run a call center, can't upgrade just yet. I'm looking for a way to send Blacklist calls to either a custom destination or a...
View ArticlePick up ringing phone, caller hears busy signal
@jmelson wrote: Had a power failure, the FreePBX computer rebooted. Now, we are having a lot of "hang up" calls on ONE line. These are where the phone rings, you answer it, and hear either a dial...
View ArticleWhat is going on now?
@bksales wrote: all of a sudden all the pbx's we manage are showing "error" on the console - the message says an ajax error and to check the console. is this all caused by the latest release? these...
View ArticleOutgoing Fax notification emails stopped sending
@plapierre wrote: We are running Freepbx version 13 and have Fax Pro installed. On Sept 6th outgoing faxes sent through UCP stopped sending. I have reviewed the /var/log/maillog and there is no...
View ArticleAlready answered calls still appearing in phones
@Nebulak wrote: First let me start with our general setup. We are a high volume call center and have and landline that is forwarded to our SIP provider. The calls then move into a queue where everyone...
View ArticleRecord call on demand before making call? *1 works once call is connected
@jamesr219 wrote: Hello, I'd like to be able to start an outgoing and have it recorded. We typically do not record our outgoing calls and *1 does work once the call is connected. Is there a way I can...
View ArticleChange Volume on MOH Gone? V13
@mvogel4949 wrote: Changing the volume on MOH for FreePBX 13 seems to be gone. Is that true? Posts: 2 Participants: 2 Read full topic
View ArticleClik here to view.
RasPBX Advanced Settings Page Blank
@S_REX wrote: Hello - I have recently installed RasPBX (FreePBX 13) and in the admin console under 'Advanced Settings' i have the usual warning messages at the top about using caution, but then the...
View ArticleSet CID invalid number
@vespino wrote: I'm using Set CID to add a "0" to incoming the called ID so I can call the number back using the correct outbound CID. I'm now facing this issue: When a CID is +xxxxxxxxxx the CID is...
View ArticleDahdi Card not connecting
@mohammed_kakuji wrote: Hi all, I have a A200 Sangoma card installed on my FreePBX System. PBX Firmware: 6.12.65-29PBX Service Pack: 1.0.0.0FreePBX 13.0.188.1Current Asterisk Version: 13.9.1 I can...
View ArticleForce auto answer
@bainwave wrote: Hello All,My scenario is as follows...Server is on Elastix 2.3 with unembedded Free PBX (2.8.1.4). Hardware Digium TE 131 PRI Card.Flow:Call lands on the elastix server --->...
View ArticleProblem with call forward through code *720
@system85 wrote: Hi,I set a call forward via the * 720 code from an extension to a mobile number .In practice , if the cell on which I should receive the call can not be reached , the person whoi is...
View ArticleForwarding to cell phone only from extension dial not queue group
@tradesync wrote: I have an IVR when you dial in to the main DID that allows the selection of 5 options as well as being able to dial an extension directly. The 5 selections are queue groups that ring...
View ArticleTrunk channel UNAVAILABLE to call out?
@josephchrz wrote: Hello i have a grandstream 4104 everything is working but i lost my pbx hard drive die out i had to start all over. So i got everything back and i can call in But when i call out it...
View Article