Quantcast
Channel: General Help - FreePBX Community Forums
Viewing all articles
Browse latest Browse all 12610

Cisco 7940 with free pbx

$
0
0

@Don44 wrote:

I have installed free FreePBX 13.0.190.11 and have flashed a cisco 7940 to sip and am trying to get it to connect to the pbx server it will not make or receive calls I am pretty sure the con fig files are right because the phone loads the files and shows an extension number but can not make calls. Here are my config files

SIP00146A12D7C1.cnf

# Line 1 Settings
line1_name: "100"                      ; Line 1 Extension\User ID
line1_displayname: "100"               ; Line 1 Display Name
line1_authname: "100"                  ; Line 1 Registration Authentication
line1_password: "1234"          ; Line 1 Registration Password
line1_shortname: "100"                 ; Line 1 Short Name

# Line 2 Settings
line2_name: ""                          ; Line 2 Extension\User ID
line2_displayname: ""                   ; Line 2 Display Name
line2_authname: "UNPROVISIONED"         ; Line 2 Registration Authentication
line2_password: "UNPROVISIONED"         ; Line 2 Registration Password
line2_shortname: ""                     ; Line 2 Short Name


SIPDefault.cnf

proxy_backup_port: "5060"

# Outbound Proxy info
outbound_proxy: ""
outbound_proxy_port: "5060"

# NAT/Firewall Traversal
nat_enable: "0"
nat_address: ""
voip_control_port: "5061"
start_media_port: "16384"
end_media_port: "32766"
nat_received_processing: "0"

# Proxy Registration (0-disable (default), 1-enable)
proxy_register: "1"

# Phone Registration Expiration [1-3932100 sec] (Default - 3600)
timer_register_expires: "3600"

# Codec for media stream (g711ulaw (default), g711alaw, g729)
preferred_codec: "none"

# TOS bits in media stream [0-5] (Default - 5)
tos_media: "5"

# Enable VAD (0-disable (default), 1-enable)
enable_vad: "0"
# Allow for the bridge on a 3way call to join remaining parties upon hangup
cnf_join_enable: "1" ; 0-Disabled, 1-Enabled (default)

# Allow Transfer to be completed while target phone is still ringing
semi_attended_transfer: "0" ; 0-Disabled, 1-Enabled (default)

# Telnet Level (enable or disable the ability to telnet into this phone
telnet_level: "2"  ; 0-Disabled (default), 1-Enabled, 2-Privileged

# Inband DTMF Settings (0-disable, 1-enable (default))
dtmf_inband: "1"

# Out of band DTMF Settings (none-disable, avt-avt enable (default), avt_always - always avt )
dtmf_outofband: "avt"

# DTMF dB Level Settings (1-6dB down, 2-3db down, 3-nominal (default), 4-3db up, 5-6dB up)
dtmf_db_level: "3"

# SIP Timers
timer_t1: "500" ; Default 500 msec
timer_t2: "4000" ; Default 4 sec
sip_retx: "10" ; Default 11
sip_invite_retx: "6" ; Default 7
timer_invite_expires: "180" ; Default 180 sec

# Setting for Message speeddial to UOne box
messages_uri: "*97"

# TFTP Phone Specific Configuration File Directory
tftp_cfg_dir: "./"

# Time Server
sntp_mode: "unicast"
sntp_server: "192.168.0.150"
time_zone: "central"
dst_offset: "0"
dst_start_month: "Mar"
dst_start_day: ""
dst_start_day_of_week: "Sun"
dst_start_week_of_month: "2"
dst_start_time: "02"
dst_stop_month: "Nov"
dst_stop_day: ""
dst_stop_day_of_week: "Sunday"
dst_stop_week_of_month: "1"
dst_stop_time: "2"
dst_auto_adjust: "1"

# Do Not Disturb Control (0-off, 1-on, 2-off with no user control, 3-on with no user control)
dnd_control: "0" ; Default 0 (Do Not Disturb feature is off)

# Caller ID Blocking (0-disabled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
callerid_blocking: "0" ; Default 0 (Disable sending all calls as anonymous)

# Anonymous Call Blocking (0-disbaled, 1-enabled, 2-disabled no user control, 3-enabled no user control)
anonymous_call_block: "0" ; Default 0 (Disable blocking of anonymous calls)

# Call Waiting (0-disabled, 1-enabled, 2-disabled with no user control, 3-enabled with no user control)
call_waiting: "1" ; Default 1 (Call Waiting enabled)

# DTMF AVT Payload (Dynamic payload range for AVT tones - 96-127)
dtmf_avt_payload: "101" ; Default 100

# XML file that specifies the dialplan desired
dial_template: "dialplan"

# Network Media Type (auto, full100, full10, half100, half10)
network_media_type: "auto"

#Autocompletion During Dial (0-off, 1-on [default])
autocomplete: "1"

#Time Format (0-12hr, 1-24hr [default])
time_format_24hr: "0"

# URL for external Phone Services
services_url: "http://www.singlewire.com/freeservices/menu"

# URL for external Directory location
directory_url: ""

# URL for branding logo
logo_url: ""

# Remote Party ID
remote_party_id: 1 ; 0-Disabled (default), 1-Enabled

Thanks for your help

Posts: 1

Participants: 1

Read full topic


Viewing all articles
Browse latest Browse all 12610

Trending Articles



<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>