Quantcast
Channel: General Help - FreePBX Community Forums
Browsing all 12657 articles
Browse latest View live

FreePBX 14 on Docker

@psdk wrote: Anyone has experience about this topic? Posts: 1 Participants: 1 Read full topic

View Article


FreePBX 13 reload error

@kelliott wrote: When I run a fwconsole reload I get the following output:Reloading FreePBXError(s) have occured, the following is the retrieve_conf output:exit: 255PHP Fatal error: Allowed memory...

View Article


Detecting Original distination number on incoming forwarded call

@someguyin831 wrote: I have been searching for weeks on a way to route an incoming call based on the following conditions:1. The incoming call was forwarded.2. read the originally dialed phone...

View Article

Softphones, External Clients, VPN, Etc

@nmarques wrote: I have a few questions with best configuration options.... If we want our users (less than 10) to be able to log into softphone software at home or on mobile phones, can this be done...

View Article

Image may be NSFW.
Clik here to view.

Asterisk 15 - Woo Hoo - Video Conferencing!

@GSnover wrote: Here is the announcement: blogs.digium.com Open Source Asterisk 15 Released - Inside the Asterisk Today marks the launch of Asterisk 15, the next great release of Asterisk.  Asterisk...

View Article


Sip Trunk Service Block by Firewall Module

@zfsag wrote: Sip Provider uses ip authentication The Firewall will block the server ip of the host after several phone calls. Copied from wiki (Note that you do not have to add configuration for...

View Article

How to point an inbound route to an outbound

@Zirwo01 wrote: Is it possible to point forward an inbound call for example form cucm to the outbound route. Currently I am able to call ext from cucm into freepbx. but when I try to dial an external...

View Article

Apply same settings to extentions

@adamx77 wrote: Under extensions>advanced settings, I’d like to permit a specific IP range which is the IP from the SIP provider. Is there a way to apply this to all extensions at once? Or do you...

View Article


Send inbound calls through announcement

@gw22 wrote: We have a number of DID's and want to be able to send each DID through the announcement "Call Will Be Recorded" prior to being sent the the proper destination. Is there a way to send all...

View Article


Firewall turns on by itself

@monstermatt2 wrote: i dont know if this is a bug or not, but in the installation i turned off and disabled the firewall (i have external firewall), so after the install, i add my extensions to my...

View Article

Yealink T46G T29G not listed

@garias wrote: hello guys, i need some help making those to devices work on OSS EPM ? or any guide on how to make them work ? Posts: 1 Participants: 1 Read full topic

View Article

Voicemail Hardcoded Max Time Limit (if any)

@chrischevy wrote: Is there a hardcoded time limit for voicemail messages ?I have a customer who wants to be able to record very long messages (could be anything from 30 to 90 minutes) for a very...

View Article

cel.MYD too big

@handlespro wrote: Hi my cel.MYD is getting too big for my liking. Can someone show me how to delete some entries on it? Thanks. Here is my ls -lh /var/lib/mysql/asteriskcdrdb/ total 6.4G-rw-rw----. 1...

View Article


How to re-write forwarded “follow-me” caller ID?

@hwcltjn wrote: Sam calls Julie's direct dial line and because she's not at her desk (and because of a follow me rule) the call is forwarded to her mobile. FreePBX forwards the call through the...

View Article

Allow admin group to administrate all users in ucp

@gordon wrote: How do I allow an administrator to edit all extensions from the UCP? I.e. someone didn't set their call forwarding to unconditionally go to the correct extension before leaving for...

View Article


FreePBX on Hyper-V -- Strictly for learning

@ALombardi wrote: There has been some discussion on here that I've seen regarding PBX in a VM. I know it can only be done under certain conditions. Our phone guy at the office isn't very forthcoming...

View Article

Inbound Not A Working Number

@oren09 wrote: My PBX had previously been working just fine with no issues. I rarely use it, though.I decided to randomly call my number one day and received a message "The number you have dialed is...

View Article


Convert dialed words to numbers

@GPz1100 wrote: Any thoughts on how to convert dialed words (through sip client) to numbers. For example, dialing 1-800-gofedex or 1-800pickups would convert to the letters to their respective digits....

View Article

All circuits are busy

@frenaud wrote: When we hit 8 "External calls", all outgoing calls return "All circuits are busy" message.Our main Outbound Route contains 11 Trunk Sequences. Shouldn't that give us 11 simultaneous...

View Article

SysAdmin VPN Question

@mvogel4949 wrote: Can I utilize the VPN built into System Admin Pro to create a VPN between say a Yealink phone to the FreePBX or does the VPN built in server only work with sangoma phones? Thanks...

View Article
Browsing all 12657 articles
Browse latest View live