Quantcast
Channel: General Help - FreePBX Community Forums
Browsing all 12590 articles
Browse latest View live

Site-site incoming call routing question

@SteveV wrote: We have 2 locations each running a FreePBX 12 (Asterisk 13.5.0) server with PRI. The sites are connected to one another via a 100Mbs fiber connection and the FreePBX servers via an IAX2...

View Article


Schedule phone start and end

@Eagle75au wrote: Hi all, Currently we dial *280 at 9am each morning to turn on our phones and again at 5pm to turn them off, my question is, is there a way to automate this process via task scheduler...

View Article


Image may be NSFW.
Clik here to view.

Inbound E.164 Caller ID - How to change the display format?

@acentrica wrote: We are based in the UK and our telephone carrier has recently informed us that they are about to start sending the Caller ID of inbound calls over our SIP Trunks in the standard...

View Article

SIP SHOW PEERS - Port 5061?

@dave69s wrote: I just setup 150 Yealink phones on my FreePBX 12 configuration. All my phones are configured for port 5060 in the server and extension setting, but SIP SHOW PEERS shows all of them on...

View Article

Yealink Sidetone settings

@edlentz wrote: We have a number of Yealink T38G phones that have an extreme amount of sidetone. We have them at the latest firmware and there doesn't seem to be any way to change the sidetone...

View Article


Allworx 9212?

@Obliterous wrote: Has anyone gotten an Allworx 9212 working with FreePBX? Posts: 1 Participants: 1 Read full topic

View Article

Call Recording

@richelle_vpg wrote: Hello, Is there a possible way to setup something where you can press a button on a phone to play a recorded message that says that the call will be recorded and then when the...

View Article

"all circuits are busy now"

@neuronetv wrote: forgive me blowing off steam but this problem is driving me bonkers. I'm in the UK and I can dial normal (11 digit) numbers from my usual extension no problem but I'm trying to get...

View Article


Reload failed because retrieve_conf encountered an error: 1

@mackrec wrote: Hi there,I've recently built a FreePBX using the latest raspbx-06-03-2016 image on a raspberry pi 2 to replace our existing switch that has faults. However, whenever I try to apply a...

View Article


DAHDI Fax Detection Time

@kurtwoods wrote: I have fax detection enabled for the inbound routes on by T1/PRI, and if I set the detection time to 10 seconds (which is actually closer to 15) it will work. However, no one is...

View Article

Linksys SPA962 Paging puts active call on hold

@koreyb wrote: Hi There, We have a Linksys SPA962 with 3 different extensions configured on this phone. When someone sends out a page to all extensions and someone happens to be on a call on EXT 2 or...

View Article

Time conditions - permanent override does not stay permanently

@Gonz wrote: few hours later it says: Current: No Override V13.0.26 PS: Cant´t log in in to FreePBX Issue Tracker (You do not have a permission to log in. If you think this is incorrect, please...

View Article

Unsigned Signature

@duncanidaho wrote: I upgrade to freepbx 13 and I am having an issue with unsigned module contact directory. Is there a link to a download so I can upload the proper signature? Thanks Mike Posts: 1...

View Article


Fresh install

@Prick0 wrote: Trying to install free pbx Having just a few issues$ echo $BASH_VERSION4.3.39(3)-release Brand new to git-hub and not sure how to get the distro package into the respiratory as well as...

View Article

Digium TE PRI lost when upgrading from 6.12.65-27 to 10.13.66-1

@marcm wrote: I just carried out upgrades through the CLI. Starting from a perfectly running 6.12.65.27.I now have reached 10.13.66-1 and can't find the Digium PRI card anymore.Digium Card is TE235B...

View Article


iSymphony not running

@bgroper wrote: Hi ForumI been using FreePBX distro for a while, currently using version 12.I'm trying a new test rig with freshly installed and updated v 13, but can't seem to get iSymphony running.....

View Article

Futex on FreePBX distro

@voipmuch wrote: Hell everyone, I have many FreePBX distro's, and only 1 of them appears to have something I know I did not install: FUTEX This is located in /var/www/html Any idea what this is and...

View Article


FreePBX CDR Reports Player

@korda wrote: Hello.When I listen wav file in CDR Reports Player I can hear only part of full file. For example file has duration 6m5s, but player can play only 4m13s. But when I download file I can...

View Article

FPBX 13.x Backup to AIX host issues

@WB3FFV wrote: I have a strange one, and am looking for ideas on how to track down, or debug this issue with backups. I have a client with an IBM Power Server running AIX, and they want me to backup...

View Article

Image may be NSFW.
Clik here to view.

Best path for upgrading from Trixbox 2.8.0.4 to newest version of FreePBX

@jlayton wrote: Hello, At my job, we are planning on upgrading from Trxibox 2.8.0.4 to FreePBX 13, but I am assuming there is not a straight path for this upgrade since Trixbox is so old. I am aware...

View Article
Browsing all 12590 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>