Downgrade to Asterisk 13 causes 403 forbidden
@dsproul wrote: I have been trying to switch my asterisk version from 14 to 13 by using the asterisk-version-switch command. Everything looks like it worked fine, the system shows the correct version...
View ArticleEmail call recordings?
@sentinelace wrote: I need to record on demand using *1. When the call ends, I need it to email that recording to the email address on that extension. How is this done? Posts: 3 Participants: 3 Read...
View ArticleLimit to IAX2 connections?
@mvogel4949 wrote: If I want to network two freepbx systems I am familiar with the IAX2 Trunk setup between them. Is there a limit to the number of IAX2 trunks or is it limited only by your processor...
View ArticleAsterisk full log
@Chrisb45 wrote: Hi i set the rtp set debug on command and then looked in the full log found in /var/log/asterisk to find the output but the only thing showing over and over again was the below is...
View ArticleFreePBX 14.0.1.20 - Unable to connect to the UCP Node Server because: 'Error:...
@noahbalboah91 wrote: When logging into UCP on any account I'm getting "Unable to connect to the UCP Node Server because: 'Error: xhr poll error'" I've removed and reinstalled UCP, ran all system...
View ArticleUCP is missing the call forward settings
@BenBeige wrote: I had an extension that was setup to user call forwarding at some point and it did not have a user assigned to it, I don't have access to the phone at this time and wanted to...
View ArticleFirst steps to setup - not as easy as I thought!
@simple wrote: So, I'm new here but I have many years experience in setting up PBX's; just not Linux/Asterisk based. This system is just not giving me the queue's I'm expecting and posing lots of...
View ArticleRecordings Files 0 bytes
@garias wrote: Hello guys, im having problem with my Recent FreePBX Install : FreePBX 14.0.1.14 from Freepbx distro the phone message plays it back perfect, the email attachments have it perfect, just...
View ArticleHow to replace running FreePBX server with better hardware?
@cfapress wrote: After two attempts I'm stumped. GOAL : replace running FreePBX server with same software but better hardware We have FreePBX running on a dual core desktop machine. We purchased...
View ArticleFPBX14 Firewall status not updating
@XARIS33 wrote: Firewall works ok but all stats show 0, as well as registered endpoints etc. Posts: 2 Participants: 2 Read full topic
View ArticleCID Lookup module - selection of groups
@mstitdk wrote: Hallo under CID Lookups i have made a look up to contact manager i have 11 groups i want this look up to use, after i have selected them and hit "Submit" it have only selected 3 of...
View ArticleAllow CID Lookup to lookup into Contact manager for Caller ID Name
@mstitdk wrote: Hallo I have entered a lot of conctacts under Conctact Manager - and like that i can grpupe them as i want to. And i have made a CID lookup to 'Contact Manager' and selected some of...
View ArticleConfig S500 with Firewall Enabled
@scstone18 wrote: I'm trying to get my s500 phones to receive their configuration with the responsive firewall enabled. I'm trying to use the Sangoma Zero Touch Configuration. Posts: 4 Participants: 2...
View ArticleI would like to launch a call and give a warning
@claloano wrote: I would like to launch a call and give a warning Very simplyFrom a trigger event, the PBX should call a given number and perform a specially prepared audio alert Quancuno give me a...
View ArticleIssues with IVR recordings quality
@DamianB wrote: Hey Everyone, All is going really well with my FreePBX distro. One thing is really getting to me though. I have tried recording my IVR recordings a couple of different ways. 1 through...
View ArticleConnecting my VoIP to my Avaya CM system
@robertkwild wrote: hi all, i have set up a freePBX server and now i want to connect it up to my current avaya CM system so the two can link together for calls/transfers etc atm the way i have linked...
View ArticleUCP error division by zero
@sysdg wrote: Hi community, After importing the configuration from an Elastix 2.5 through the migration tool, UCP web page does no load correctly.It shows: Hubo un error tratando de cargar el...
View ArticleLoss of inbound GV calls connectivity after period of time
@GPz1100 wrote: I have freepbx configured with several gv accounts. Of those, 1 seems to lose ability to receive calls after a period of time. Making an outbound call refreshes things and it works...
View ArticlePJSIP Not Reachable Option
@fgunno wrote: I try to setup a Ring Group for an Not Reachable option for some extension, but if the extension is a PJSIP, the Not Reachable option is not working is it a bug? or something special...
View ArticleCan't get phones to sync ntp after converting to EPM
@demani wrote: So this may be related or it may not be. I just updated to the commercial EPM but when I reconfigure phones under the new system they don't sync the clock (Polycom 560 and Yealink w52p...
View Article