DID Inbound Routing - Is there a way to route to "last agent"?
@BigChief wrote: Say I have 10 agents here who all make outbound calls using our 800 number as the caller ID. If a customer misses our call and so makes a call back to our 800 number, is there any way...
View ArticleClik here to view.
Problems logging to external syslog server
@jes1111 wrote: Hi - I'm new to FreePBX (and Linux). We've bought a Sangoma FreePBX 60 to run the phones at our private nursing home. I've got everything working nicely but we've had two instances of...
View ArticleLooping a prerecorded page
@andersonhaulage wrote: My safety committee has asked me if there was a way to setup a prerecoded message and send it as a page, looping through it for a certain amount of time. As in, we need to...
View ArticleRequest for phone model suggestion
@nkamkar wrote: Hello all I need to buy a voip phone with the following requirements and I was wondering if you lovely folks could recommend something cheap and cheerful to do the job. I need it to be...
View ArticleWifi SIP Phones
@kbocek wrote: As I am slowly putting together all the pieces of my old proprietary analog system, I'm having difficulty finding a decent wifi based SIP phone. I see lots of DECT based phones but I...
View ArticleEmergency number
@telili wrote: Somebody knows how to set a specific CID for incoming call, i am about to built a voip system with freePBX, the customer wants me to set up a very short number as an Emergency number...
View ArticleFPBX13-A13- Cannot add IVR get page errors
@DarkQuark wrote: Greetings, I am simply trying to add an IVR on a new system (see details below). When I try I get a webpage full of errors. Everything else on the system has worked fine to this...
View ArticleNo dial tone on indial. But phone is ringing
@swalz wrote: Hi, I ran the online upgrade to FreePBX 13.0.109 and now when I dial in I have no dial tone on my mobile.But the internal phone is ringing? This is for all extensions I try to ring.I a...
View ArticleInbound call come 1st or time condition?
@arkoi wrote: Can't receive a inbound call using time conditions ? Posts: 1 Participants: 1 Read full topic
View ArticleFreepbx 13 on Centos 7
@michaelschefczyk wrote: Dear All, Experimenting with Freepbx on Centos 7 according to the wiki guide (http://wiki.freepbx.org/display/FOP/Installing+FreePBX+13+on+CentOS+7), I would like to confirm,...
View ArticleSame Extension on Multiple Phones
@jhildenburg wrote: I'm running FreePBX 13/Asterisk 13 and have the commercial endpoint manager installed/licensed. All modules updated fully. I'm trying to register the same extension on more than...
View ArticleGetting A PSTN Dialtone On An ATA
@kbocek wrote: I see this old thread with no answer: How To Get A PSTN Dialtone I have something similar, a couple of Grandstream ATAs. I previously had them misconfigured with extensions pointing at...
View ArticleIs this system feasible?
@kevid6 wrote: Since I recieved no valid answer,, I drop this Posts: 3 Participants: 2 Read full topic
View ArticleDigium phones config module
@NooNoo wrote: FreePBX 13.0.109 custom install on 64bits Centos 7 with Asterisk 13.8.0 After installing the Digium Phones Config Module 2.11.3.0 I'm not able to do a reload of Freepbx. Error: Error(s)...
View ArticleHow to deactivate cel
@gatozgz wrote: Hello good evening, I only want the reports from CDR, I dont need CEL reports. There is anyway to deactivate CEL? If I modify on:cel_general_custom.confenable=no And restart...
View ArticleMore than three cases of Asterisk 13.8.1 Crashing
@xptpa2020 wrote: I receive this message in /var/log/messages when I hear that calls are dropping and can notice that Asterisk has only been running for xx amount of minutes: May 2 10:16:02 fpbx...
View ArticleManually importing call data from older version(s)
@cw89 wrote: I recently transitioned from Elastix 2.5 to FreePBX 13. I built a new box for FreePBX and configured everything from scratch. The only data that needs to be brought over is the call...
View ArticleUnable to access VM "My Mailbox' feature code
@kristiandg wrote: Good morning all. This morning we came in and were unable to access voicemail. Our feature code is *0# for voicemail (and has worked for years on various deployments). When we...
View ArticleTools to diagnose QOS issues?
@usatraveler wrote: I am pretty new to FreePBX and phone systems in general so looking for some guidance. We are running FreePBX 12.0.76.2 offsite provided by a third party. There are times that I...
View ArticleIs preloaded Music On Hold public domain?
@Lumute wrote: Hi all, We have been receiving calls from Socan about paying licensing fees for the music we use in our phone system to avoid getting sued... these people are a real pest, I asked what...
View Article